To size a lithium-ion forklift battery, match the truck's required voltage and minimum weight first, then pick the capacity (amp-hours) that covers the energy your truck uses between charging opportunities, with a buffer for depth of discharge and battery aging. Your duty cycle, not the size of the old lead-acid battery, should drive that capacity decision.
Many fleets simply replace a lead-acid battery with a lithium-ion pack of the same amp-hour rating. That often works, but it can leave money on the table. Lithium-ion packs can be opportunity charged during breaks, which changes the math entirely. A right-sized pack can run multiple shifts without a battery swap, while an oversized one adds cost you never use.
This guide walks fleet managers through a five-step sizing method, a worked example, and how each Flux Power product line fits common duty cycles.
A forklift duty cycle is the pattern of work a truck does over a shift: how many hours it runs, how hard it works during those hours, and when it sits idle. Two trucks of the same model can have very different duty cycles.
The factors that shape energy use include:
Lead-acid batteries are typically sized to survive one full shift, then swapped or charged for about eight hours plus cooling time. That forces fleets to buy spare batteries and dedicate floor space to battery rooms.
Lithium-ion changes the model. Because lithium-ion packs accept partial charges without damage, capacity only needs to cover the energy used between charges, not an entire day. As covered in our guide to lithium-ion charging best practices, short, frequent charges support battery health rather than degrade it.
That means the right answer depends on two linked decisions: battery capacity and charging strategy.
Start with the truck, not the battery. Check the data plate and OEM spec sheet for:
Voltage is not negotiable. Weight matters too: Flux Power packs offer truck adapters to meet OEM weight requirements, so a lithium-ion pack can stand in for a heavier lead-acid battery without affecting stability.
Next, determine how much energy each truck consumes, in kilowatt-hours (kWh) per operating hour. Good data sources include:
Measure your heaviest-working trucks, not the fleet average. Sizing to the average leaves your busiest trucks short at the end of a shift.
List every point in the day where a truck could plug in: scheduled breaks, lunches, shift changes, and natural idle periods. Note how long each window lasts and whether a charger is nearby.
The longest stretch between charging windows sets your minimum capacity. A truck that charges every two hours needs far less capacity than one that must run a full eight-hour shift untouched.
Use this formula to estimate the usable energy a pack needs:
Required kWh = (kWh per hour × hours between charges − kWh recovered during charging) ÷ usable depth of discharge × (1 + aging margin)
Then convert to amp-hours: Ah = (Required kWh × 1,000) ÷ system voltage
Planning guidelines:
Capacity and charger output work together. A charger's power (kW) multiplied by the charge window (hours) tells you how much energy you can put back. If your plan relies on 30 minutes of charging at lunch, confirm the charger can actually deliver that energy in 30 minutes. Our forklift battery charger guide covers charger types and infrastructure considerations.
Illustrative numbers only. Actual consumption varies by truck, load, and application. Talk to your Flux Power Energy Expert for a full fleet assessment.
A distribution center runs 48V Class I counterbalance forklifts across three eight-hour shifts. Telematics show the busiest trucks use about 4 kWh per operating hour and run about 7.5 hours per shift.
|
Scenario |
Energy per shift |
Recovered by charging |
Required capacity |
Pack fit |
|
No charging during shift |
30 kWh |
0 kWh |
30 ÷ 0.8 × 1.2 = 45 kWh (≈940 Ah at 48V) |
Needs a swap or oversized pack |
|
Opportunity charging at breaks and lunch (~1 hour total at ~8 kWh/hr) |
30 kWh |
~8 kWh |
22 ÷ 0.8 × 1.2 = 33 kWh (≈690 Ah at 48V) |
48V, 840 Ah (≈40 kWh) with headroom |
With opportunity charging, a single 48V, 840 Ah pack covers each shift with room to spare, and the truck recharges between shifts. No spare batteries, no battery room, no swaps. A 630 Ah pack (≈30 kWh) would fall just short for these busiest trucks, but could suit lighter-duty trucks in the same fleet.
That last point matters: in a mixed fleet, sizing truck by truck usually beats a one-size-fits-all purchase.
Flux Power builds lithium-iron battery packs for Class I, II, and III electric forklifts. Each series is designed for a specific truck type and its typical work pattern.
|
Series |
Equipment |
Voltage |
Capacity options |
Typical duty cycle |
|
Class I counterbalance forklifts |
36V, 48V, 80V |
Up to 840 Ah |
Heavy loads, dock work, high-intensity multi-shift |
|
|
Class I 3-wheel counterbalance forklifts |
36V (L36), 48V (L48) |
L36: 630 or 840 Ah |
Tight-turning, high-throughput warehouse aisles |
|
|
Class II narrow aisle (M36); Class III end and center riders (M24) |
36V, 24V |
M36: 630 or 840 Ah; M24: 420 Ah |
Order picking, reach work, frequent stop-and-go |
|
|
Class III walkie pallet jacks |
24V |
S24: 105 or 210 Ah |
Intermittent, light-to-moderate use; UL Type EE options available |
A few selection tips:
Explore how these packs fit specific operations on our industries page.
Duty cycles change. Volume grows, shifts get added, and trucks get reassigned. A battery that was right-sized at deployment can become undersized two years later.
Fleet energy management software closes that gap. SkyEMS tracks state of charge, utilization, charging behavior, and battery health across every connected pack. That data shows which trucks run close to empty, which are underused, and when to rebalance the fleet. Learn more in How Smart Battery Data Helps Manage Forklift Fleets More Efficiently and Intelligent Fleet Power.
The fastest way to right-size a lithium-ion forklift battery is to test it in your own operation. Flux Power's demo battery program lets you trial a pack on your trucks and duty cycles before committing to a fleet conversion.
Talk to a Flux Power energy expert to review your duty cycle, charging windows, and the X, L, M, or S Series pack that fits each truck.
Start with the truck's required voltage and minimum battery weight. Then measure energy use per operating hour, map your charging windows, and calculate the capacity needed to cover the longest stretch between charges at about 80% depth of discharge, plus a 10–20% aging margin.
You can, but it may not be the best fit. Lead-acid batteries are sized to last a full shift without charging. Lithium-ion packs can be opportunity charged during breaks, so the right capacity depends on your charging windows and duty cycle, not the old battery's rating.
A forklift duty cycle is the pattern of work a truck performs over a shift, including run hours, load weights, lift heights, travel distance, operating environment, and idle time. It determines how much energy the truck uses and when it can recharge.
Opportunity charging lets lithium-ion packs recover energy during breaks, lunches, and shift changes. Because energy is added back throughout the day, the battery only needs to cover the work done between charges. That often allows one pack per truck across multiple shifts, with no battery swaps.
Yes. Cold and freezer environments increase energy consumption and can limit charging rates. Add extra capacity margin for cold storage duty cycles and consider battery packs with integrated heaters that are designed for low-temperature operation.
X-Series fits Class I counterbalance forklifts at 36V, 48V, or 80V. L-Series fits Class I 3-wheel forklifts. M-Series covers Class II narrow aisle (M36) and Class III end and center riders (M24). S-Series fits Class III walkie pallet jacks.
Service life depends on duty cycle and charging habits. Flux Power lithium-ion packs are rated for more than 3,500 cycles at 80% depth of discharge. Sizing the pack correctly and following charging best practices helps it reach that rating.
Yes. Flux Power's demo battery program lets fleets trial a lithium-ion pack on their own trucks and duty cycles. It is the most reliable way to confirm sizing before a full fleet conversion.